to be fair, you don't need to go historical on it, but you DO need some basic aspect to what should be a "bowie"
this is one of the many ref on what a bowie should be :
"According to an 1847 article, the Bowie knife was originally designed to fill the need for a wearable, convenient close combat weapon - a short sword much shorter than the saber or other swords of the day, yet still possessing a heavy blade. This cleaver-like blade had enough weight to give the blade sufficient force in a slashing attack, while permitting the use of cut-and-thrust sword fighting tactics.[10] By this time the 'Bowie knife' was already being made in a variety of sizes, with the optimum blade length similar to "that of a carving knife"[10][11] The blade design was described as:
"Back (spine) perfectly straight in the first instance, but greatly rounded at the end on the edge side; the upper edge at the end, for a length of about two inches, is ground into the small segment of a circle and rendered sharp...The back itself gradually increases in weight of metal as it approaches the hilt, on which a small guard is placed. The Bowie knife, therefore, has a curved, keen point; is double-edged for the space of about two inches of its length, and when in use, falls with the weight of a bill hook."[10]
Most later versions of the Bowie knife had a blade of at least 8 inches (20 cm) in length, some reaching 12 inches (30 cm) or more, with a relatively broad blade that was an inch and a half to two inches wide (4 to 5 cm) and made of steel usually between 3⁄16 to 1⁄4 in (4.763 to 6.350 mm) thick. The back of the blade sometimes had a strip of soft metal (normally brass or copper) inlaid which some believe was intended to catch an opponent's blade while others hold it was intended to provide support and absorb shock to help prevent breaking of poor quality steel or poorly heat treated blades. Bowie knives often had an upper guard that bent forward at an angle (an S-guard) intended to catch an opponent's blade or provide protection to the owner's hand during parries and corps-a-corps.
Some Bowie knives had a notch on the bottom of the blade near the hilt known as a "Spanish Notch". The Spanish Notch is often cited as a mechanism for catching an opponent's blade; however, some Bowie researchers hold that the Spanish Notch is ill-suited to this function and frequently fails to achieve the desired results. These researchers, instead, hold that the Spanish Notch has the much more mundane function as a tool for stripping sinew and repairing rope and nets, as a guide to assist in sharpening the blade (assuring that the sharpening process starts at a specific point and not further up the edge), or as a point to relieve stress on the blade during use.
One characteristic of Bowie knives is the clip point at the top of the blade, which brings the tip of the blade lower than the spine for better control. As the goal is to produce a sharp, stabbing point, most Bowie knives have a bevel ground along the clip, typically 1/4 of the way, but sometimes much further running the entire top-edge. This is referred to as a false edge as from a distance it looks sharpened, although it may or may not be. Regardless of whether or not the false edge is sharp, it serves to take metal away from the point, streamlining the tip and thus enhancing the penetration capability of the blade during a stab. The version attributed to blacksmith James Black had this false edge fully sharpened in order to allow someone trained in European techniques of saber fencing to execute the maneuver called the "back cut" or "back slash".[6] A brass quillon, usually cast in a mold, was attached to protect the hand.
The Bowie knife's design also lends itself to use as a hunting knife for skinning or butchering game. The curved top clip bevel of the blade, when suitably sharpened, may be used to remove the skin from a carcass, while the straight portion of the blade edge, toward the guard, can be used for cutting meat. This is similar in concept to the traditional Finnish hunting knife, the "puukko" (though the typical early 19th-century Bowie knife was far larger and heavier than the typical puukko). Arkansas culturalist and researcher Russell T. Johnson describes the James Black knife in the following manner and at the same time captures the quintessence of the Bowie Knife: "It must be long enough to use as a sword, sharp enough to use as a razor, wide enough to use as a paddle, and heavy enough to use as a hatchet."[6][12] Most such knives intended for hunting are only sharpened on one edge, to reduce the danger of cutting oneself while butchering and skinning the carcass.
Earlier variants of the Bowie knife can be seen looking at European seax's, a knife/short sword used every day by the Vikings, Anglo Saxons, and Germanic people of the Dark Ages. History shows the evolution of the blade from a simple round ended multi purpose tool to a clip pointed, heavy backed knife or short sword used as a side arm after initial attacks rendered a broken spear or long sword useless.[dubious – discuss]"
you can use that text as a ref, but please keep the fantasy at the minimum and please stay as close to the original design as possible
here some personal idea on what a bowie should look like to keep as ref
please tell us why you think your model should be the king of all bowie.
here some idea (your choice don't need to be identical but must at least follow a similar design or follow a similar pattern. )


